Help: Neuer Knoten - keine Verbindung zu FFKA Supernode

Hallo alle,
bin neu im Thema FF. Habe heute einen Router mit firmware ausgestattet. Verbindung zu FFKA funktioniert noch nicht.
Knoten: # ffka-sulzbacher-01
Fritzbox 7490/ VDSL: Ip V4, public , WLAN Kanal 7
FF Router: TL-WR1043ND V3, WLAN Kanal 11
Einstellung: Mesh WAN, LAN: aus Mesh VPN: aktiviert
WAN-Verbindung: automatisch
SSID: alle aktiviert
Firmware von FFKA Seite: gluon-ffka-0.2.90~stable20160928-tp-link-tl-wr1043n-nd-v3.bin
Verbindung: Fritzbox LAN Port, FF Router WAN Port (Cat5 Kabel)

Problem: keine Verbindung zu FFKA Supernode, kein DHCP, keine Client IP, keine Verbindung
Knoten auf Karte nicht zusehen.

Auf welcher Leitung stehe ich? Danke für Hinweise…
reh


Info:

reh@xxx:~$ iw dev wlan0 scan
BSS 22:08:21:5b:fb:b0(on wlan0) – associated
TSF: 256741051 usec (0d, 00:04:16)
freq: 2462
beacon interval: 100 TUs
capability: ESS ShortPreamble ShortSlotTime (0x0421)
signal: -41.00 dBm
last seen: 0 ms ago
Information elements from Probe Response frame:
SSID: karlsruhe.freifunk.net
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 11
Country: DE Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
ERP:
Extended supported rates: 24.0 36.0 48.0 54.0
HT capabilities:
Capabilities: 0x11ed
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: nonmember
* non-GF present: 1
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities: Extended Channel Switching, 6
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec

BSS 22:08:21:5b:fb:b1(on wlan0)
TSF: 256717466 usec (0d, 00:04:16)
freq: 2462
beacon interval: 1000 TUs
capability: (0x0000)
signal: -35.00 dBm
last seen: 5308 ms ago
Information elements from Probe Response frame:
SSID:
Supported rates: 1.0* 2.0 5.5 11.0 6.0 9.0 12.0 18.0
DS Parameter set: channel 11
TIM: DTIM Count 0 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x0
Extended supported rates: 24.0 36.0 48.0 54.0
HT capabilities:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: non-HT mixed
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
MESH ID: 02:ca:fe:f0:0b:a2
MESH Configuration:
* Active Path Selection Protocol ID: 1
* Active Path Selection Metric ID: 1
* Congestion Control Mode ID: 0
* Synchronization Method ID: 1
* Authentication Protocol ID: 0
* Mesh Formation Info:
Number of Peerings: 0
* Mesh Capability
Accepting Additional Mesh Peerings

Hallo reh,

mittlerweile ist er da https://karlsruhe.freifunk.net/karte/. :wink:

Grüße
Jan

Danke Jan,
alles gut, hat einige Stunden gedauert bis die Route nach KA gefunden wurde.
Stand also doch neben der Leitung : :wink:
Gruß Rainer